Cateye CC-TR300TW [V3] Manuel d'utilisateur télécharger pdf (Page 21)

ENG-41

ENG

ENG-40

CR2032

Open

CR2032

RESET

Replacing battery

The product comes with factory-installed batteries. When a battery is empty, replace it

with a new one according to the following instructions.

Warning!!! :

Safely dispose of the old batteries, and do not place them within reach of children.

If a battery is swallowed, consult a doctor immediately.

* When any battery for the computer, heart rate sensor, or speed sensor is depleted, we

recommend replacing all batteries at the same time.

* The battery life shown in this manual is not definitive and it varies depending on the

use environment.

* The battery cover sealing is critical to maintain the waterproof feature.

Clean any contamination on the battery cover or the seal, and check whether it seals

correctly.

Computer

Battery life: Approx. 1 years when used for 1 hour per day.

* When the remaining battery capacity is low,

lights up.

1. Remove the battery cover on the back of the computer using a

coin, or the equivalent.

2. Insert new lithium batteries (CR2032) with the (+) sign upward,

and close the battery cover firmly.

3. After replacement, be sure to perform the restarting operation

(page 11), and set the date and time.

Heart rate sensor

Battery life: Approx. 1 years when worn for 1 hour per day.

1. Remove the battery cover on the back of the heart rate sensor

using a coin, or the equivalent.

2. Insert new lithium batteries (CR2032) with the (+) sign upward,

and close the battery cover firmly.

* The heart rate sensor consumes power when worn. Remove the

heart rate sensor whenever measurement is not required.

Speed sensor

Battery life: Approx. 1 years when used for 1 hour per day.

1. Remove the battery cover on the speed sensor using a coin, or

the equivalent.

2. Insert new lithium batteries (CR2032) with the (+) sign upward,

and close the battery cover firmly.

3. After replacement, be sure to press the RESET button on the

speed sensor, and check that the positions of the magnet and

sensor are correct and they are secured firmly.

In menu mode, cannot

change settings.

Is it currently measure-

ment?

When the auto-mode is

turned on (with

illumi-

nating), it may enter the mea-

surement mode due to elec-

tromagnetic waves.

Is it the target zone or the

measurement unit that can-

not be changed?

Only top menu can be viewed during

measurement.

Keep the unit away from any object that

may be causing interference with elec-

tromagnetic waves.

To change the target zone and

measurement unit, the resetting

operation is required.

Stop measurement, and perform the

resetting operation (page 17).

Trouble on operation

Pressing the SSE button

does not start/stop

measurement.

Check whether the auto-

mode is turned on (with

illuminating).

When illuminates, the auto-mode

is on; you cannot start or stop mea-

surement by pressing the button.

Turn off the auto-mode. (See “Setting

the auto-mode” on page 32.)

The heart rate sensor

(speed sensor) ID check

failed.

The battery for the heart rate sensor

(speed sensor) is possibly depleted.

After replacing the battery with a new

one (CR2032), check the sensor ID

again (page 29).

Lap data cannot be

stored.

Have you already com-

pleted 99 laps?

Is the lap time over 100

hours (Or is the trip lap dis-

tance over 9999.99 km)?

Is it immediately after

pressing the LAP button?

Delete data files that contain several laps

from the file view (page 27) in order to

obtain free space for lap recording.

With the recording range exceeded, the

lap cannot be measured.

Perform the resetting operation (page

17) for further measurements.

You cannot record the lap for 5 sec-

onds immediately after pressing the

LAP button.

Trouble Check Items Remedy

Abnormal values ap-

pear.

Are there any objects emit-

ting electromagnetic waves

(railway tracks, transmit-

ting stations for television,

etc.) nearby?

Keep the unit away from any object that

may be causing interference, and re-

set the data (page 17).

Measurement data can-

not be stored on the file

view.

Has the total number of laps

reached 99 points?

Delete data files that contain several

laps from the file view (page 27) in or-

der to obtain free space for lap record-

ing.

1 2 ... 16 17 18 19 20 21 22 23

Commentaires sur ces manuels

Pas de commentaire

Cateye CC-TR300TW [V3] Manuel d'utilisateur Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Cateye CC-TR300TW [V3]